support-voip-setting
VoIPアダプタ詳細設定
ご注意
- 以下からVoIPアダプタの設定変更も可能ですが、設定変更を行う場合はお客様の自己責任でお願いいたします。
- お客様にて変更され通話などに支障が生じた場合は、VoIPアダプタの再設定が必要になります。再設定は設定サポートサービス(有償)にて承ります。
1.「音声応答」
- VoIPアダプタは、音声応答メニュー"Interactive Voice Response"(IVR)により電話機から容易に設定状態の確認、設定変更が行えます。
- どちらのFXSポートでもIVRメニュー操作できます。
- 電話機からIVRメニューを使用開始するには、「***」(*を3回)をダイヤルしてください。
- IVRメニュー一覧
Menu Voice Prompt Options Main Menu “Enter a Menu Option” Press “*” for the next menu option
Press “#” to return to the main menu
Enter 01-05, 07,10, 12-17,47 or 99 menu options01 “DHCP Mode”,
“Static IP Mode”Press “9” to toggle the selection
If using “Static IP Mode”, configure the IP address information using menus 02 to 05.
If using “Dynamic IP Mode”, all IP address information comes from the DHCP server automatically after reboot.02 “IP Address “ + IP address The current WAN IP address is announced
If using “Static IP Mode”, enter 12 digit new IP address.03 “Subnet “ + IP address Same as menu 02 04 “Gateway “ + IP address Same as menu 02 05 “DNS Server “ + IP address Same as menu 02 07 Preferred Vocoder Press “9” to move to the next selection in the list:
•PCM U / PCM A •iLBC •G-726 •G-723 •G-72910 “MAC Address” Announces the Mac address of the unit. 12 WAN Port Web Access Press “9” to toggle between enable/ disable 13 Firmware Server IP Address Announces current Firmware Server IPaddress. Enter 12 digit new IP address. 14 Configuration Server IP Address Announces current Config Server Path IP address. Enter 12 digit new IP address. 15 Upgrade Protocol Upgrade protocol for firmware and configuration update. Press “9” to toggle between TFTP/ HTTP 16 Firmware Version Firmware version information. 17 Firmware Upgrade Firmware upgrade mode. Press “9” to toggle among the following three options:
- always check - check when pre/suffix changes - never upgrade47 “Direct IP Calling” Enter the target IP address to make a direct IP call, after dial tone. (See “Make a Direct IP Call”.) 71-78 Phone calls between different ports User can make internal calls between different ports inside the same GW even without being registered to SIP server. By dialing *** and 7x user can reach colleague connected to port “x” 99 “RESET” Press “9” to reboot the device
Enter MAC address to restore factory default setting
(See Restore Factory Default Settingsection)“Invalid Entry” Automatically returns to main menu
2.Webアクセス設定
- ブラウザから状態確認及び設定が可能です。
- 操作にはNetwork及び、SIPの知識が必要ですので、不慣れな方はアクセスしないでください。
- WAN portからのアクセス方法
- 電話機からWAN portアクセスをEnableに変更して下さい。(上記1.参照)
- Login passwordは別途お知らせしたものをご利用ください。
- LAN portからのアクセス方法
- LAN port側にはDHCPサーバーが機能しています。
- IPアドレスはDefaultで192.168.2.1になっています。
- Login passwordは別途お知らせしたものをご利用ください。
- Gust Login
- 以下の確認、設定が可能です
- 接続状態
- 本体IPアドレス、Web port設定など
- NAT/DHCP Server Information & Configuration:
- 管理者Login
- 全機能の設定、変更が可能になります。